A white 3D print of the California Lighthouse, a tall tapered tower on an octagonal base with a gallery and small dome on top, standing beside a few roads on open ground.

California Lighthouse in 3D

The California Lighthouse appears in city models you make here; its design may still be protected, so it isn't offered as a separate download.

Make this print Free, in your browser. Exports a slicer-ready 3MF.
  • California Lighthouse model, North view North
  • California Lighthouse model, East view East
  • California Lighthouse model, South view South
  • California Lighthouse model, West view West

© OpenStreetMap contributors

Copyright notice

The design of California Lighthouse may still be protected by copyright. It appears in the city models you make here, but it is not offered as a separate model.

Real height
30 m
On a 160 mm print
8 mm
Scale
1:3,750

30 m of the California Lighthouse, 8 mm on your shelf

Make this print opens the generator on a 600 m square around the landmark. Buildings print at close to true scale, so the landmark grows with the print size.

  1. A tall, slim tapered shaft

    The tower is a narrow cone that rises from a small octagonal base. Print slowly with good cooling so the shaft stays straight; a larger print size gives the thin column more strength.

  2. Lantern, gallery and tiny cap

    The top carries a ring-shaped gallery, a small dome and a thin finial. Print friendly adapts these to the print scale, while Full detail keeps them as modeled; a layer height of 0.12 to 0.16 mm helps.

  3. One piece with the ground

    The California Lighthouse is joined to the ground in the exported file, and the four-side check found no floating parts, so nothing needs gluing.

  4. Pick the detail for your nozzle

    In the Buildings settings, set Landmark detail to Print friendly to adapt thin parts and small details to the print scale. Full detail keeps every modeled feature, for larger prints or a finer nozzle.

  5. Colors

    Buildings, roads, water and ground arrive as separate filament slots in the 3MF. The California Lighthouse takes the building color.

  6. File format

    You get a 3MF for Bambu Studio, OrcaSlicer or PrusaSlicer. Any of them can save it as STL if you need one.

About the California Lighthouse

Locals call the California Lighthouse Faro. It rises from a limestone plateau at Hudishibana, close to Arashi Beach and the Sasariwichi dunes, on Aruba's northwestern tip, and it is the island's tallest structure. The name comes from the S.S. California, a British steamship that sank in 1891, well before the lighthouse was built around 1914 to 1916. It was erected specifically to prevent similar tragedies. The surrounding terrain resembles the moon, with jagged rocks protruding from the ground.

In 1913 Aruba belonged to the colony of Curaçao and its dependencies, so any request to build a lighthouse had to go through Curaçao. The French architect Leon Jean Marie Bourgeois drew up the design, which was approved that year. World War I made it difficult to manufacture and deliver the light, which came from the firm Barbier, Benard, et Turenne in France. In 1915 there were no direct roads to the site, so donkeys carried tools and materials from an Oranjestad harbor out to the island's westernmost point.

The influence of the Eiffel Tower can be seen in the clean, elegant, tapered cylindrical lines of the tower. Its octagonal stone base supports a lantern and a double gallery, and Cordouan, the oldest lighthouse in France, was another inspiration. Climbing to the top takes 123 steps up a spiral staircase. A weighted pendulum dropping 24 m (79 ft) regulated the light. Power switched from kerosene to acetylene in 1965 and to electricity in 1970.

About this model

The California Lighthouse is one of more than 6,500 landmark models in Mini Skyline. They are made with AI, and each one is checked in its real surroundings before release. Each model is written as code from public descriptions, plans, photographs and aerial views used only as references; no image or third-party model is copied into it. Everything around it is built from OpenStreetMap and Overture map data. Rights in the building itself, its name and any brands on it are not granted by Mini Skyline; clear them separately before you sell prints. If you would rather print the shape from map data, turn off Landmark models in the Buildings settings.

Mini Skyline is not affiliated with, or endorsed by, the owners of this building or its names and marks.

Keep exploring

More landmarks to print

Map data © OpenStreetMap contributors, Overture Maps; elevation Mapterhorn and Mapzen · Credits