A white 3D print of Beijing South railway station, a large oval roof with long ribbed fins on slim columns, among curving tracks, roads and low buildings.

Beijing South railway station in 3D

Beijing South railway station appears in city models you make here; its design may still be protected, so it isn't offered as a separate download.

Make this print Free, in your browser. Exports a slicer-ready 3MF.
  • Beijing South railway station model, North view North
  • Beijing South railway station model, East view East
  • Beijing South railway station model, South view South
  • Beijing South railway station model, West view West

© OpenStreetMap contributors

Copyright notice

The design of Beijing South railway station may still be protected by copyright. It appears in the city models you make here, but it is not offered as a separate model.

On a 160 mm print
9 mm
Scale
1:7,188

9 mm tall on a 160 mm print

Make this print opens the generator on a 1150 m square around the landmark. Buildings print at close to true scale, so the landmark grows with the print size.

  1. Long roof fins on slim columns

    The oval roof ends in long, narrow fins held up by slim columns. A larger print keeps them sturdier; print slowly, and Print friendly adapts the thinnest parts to the print scale.

  2. Smooth oval roof edges

    The big oval roof has smooth, gently curving edges. A layer height of 0.12 mm keeps those curves clean, and Full detail keeps the fine ribs on larger prints.

  3. One piece with the ground

    Beijing South railway station is joined to the ground in the exported file, and the four-side check found no floating parts, so nothing needs gluing.

  4. Pick the detail for your nozzle

    In the Buildings settings, set Landmark detail to Print friendly to adapt thin parts and small details to the print scale. Full detail keeps every modeled feature, for larger prints or a finer nozzle.

  5. Colors

    Buildings, roads, water and ground arrive as separate filament slots in the 3MF. Beijing South railway station takes the building color.

  6. File format

    You get a 3MF for Bambu Studio, OrcaSlicer or PrusaSlicer. Any of them can save it as STL if you need one.

About Beijing South railway station

Beijing South railway station, also called Beijingnan, is a large station located in Beijing's Fengtai District. It lies 7.5 km (4.7 mi) to the south of the city center, in the zone bounded by the 2nd and 3rd ring roads. Its present form opened on August 1, 2008, and it mainly serves high-speed trains. It replaced an older Beijing South station, first known as Majiapu and later renamed Yongdingmen. The older one, 500 meters (1,600 ft) from the new site, served from 1897 to 2006. The new station is the city's largest, and one of the largest in Asia.

The British architecture firm TFP Farrells designed the enormous oval-shaped station together with the Tianjin Design Institute. Over 60,000 tons of steel went into it, along with 490,000 cubic meters of concrete (17,304,000 cu ft), and 4,000 workers finished the job in under three years. The glass ceiling carries 3,246 solar panels. Shaped like a ray or a trilobite, the building sprawls over 320,000 square meters (3,444,000 sq ft), a larger area than the 258,000 square meters (2,777,000 sq ft) of the Beijing National Stadium.

The station has 24 platforms that can dispatch 30,000 passengers per hour. It is the terminus of the Beijing–Tianjin intercity railway and of the Beijing–Shanghai high-speed railway, whose trains can travel at 350 km/h (217 mph) at most. Two Beijing Subway stations, bus hubs and taxi stands are built into the same building. Reconstruction began on May 10, 2006, once the old station stopped serving trains, and the new one was complete for its reopening on August 1, 2008.

About this model

Beijing South railway station is one of more than 6,500 landmark models in Mini Skyline. They are made with AI, and each one is checked in its real surroundings before release. Each model is written as code from public descriptions, plans, photographs and aerial views used only as references; no image or third-party model is copied into it. Everything around it is built from OpenStreetMap and Overture map data. Rights in the building itself, its name and any brands on it are not granted by Mini Skyline; clear them separately before you sell prints. If you would rather print the shape from map data, turn off Landmark models in the Buildings settings.

Mini Skyline is not affiliated with, or endorsed by, the owners of this building or its names and marks.

Same skyline

More landmarks in Beijing

Map data © OpenStreetMap contributors, Overture Maps; elevation Mapterhorn and Mapzen · Credits