A white 3D print of the Niederwald Monument, a stepped stone pedestal with reliefs and small figures, topped by a tall statue, on a forested hillside with paths and a few buildings.

3D print the Niederwald Monument

A free, printable model of the Niederwald Monument, a stepped pedestal with a tall statue on top, set on a forested hillside with a few paths, roads and buildings nearby, generated from real map data in your browser.

Make this print Free, in your browser. Exports a slicer-ready 3MF.
  • Niederwald Monument model, North view North
  • Niederwald Monument model, East view East
  • Niederwald Monument model, South view South
  • Niederwald Monument model, West view West

© OpenStreetMap contributors

The model you print

Niederwald Monument in 3D

The landmark on its own, at its size on a 160 mm print. Print friendly thickens thin parts for a 0.4 mm nozzle; Full detail keeps every part.

Drag to turn it. Scroll or pinch to zoom.

Real height
38 m
On a 160 mm print
11 mm
Scale
1:3,750

38 m of the Niederwald Monument, 11 mm on your shelf

Make this print opens the generator on a 600 m square around the landmark. Buildings print at close to true scale, so the landmark grows with the print size.

  1. Raised arm on the tall statue

    The standing figure on top has a thin raised arm. Print slowly with good cooling for it; Print friendly thickens thin parts for the print scale, while Full detail keeps them as modeled for larger prints.

  2. Small figures on the pedestal

    Reliefs and small winged figures with raised arms sit around the lower levels. A layer height of 0.12 to 0.16 mm and a larger print size keep these small shapes readable.

  3. One piece with the ground

    The Niederwald Monument is joined to the ground in the exported file, and the four-side check found no floating parts, so nothing needs gluing.

  4. Pick the detail for your nozzle

    In the Buildings settings, set Landmark detail to Print friendly to adapt thin parts and small details to the print scale. Full detail keeps every modeled feature, for larger prints or a finer nozzle.

  5. Colors

    Buildings, roads, water and ground arrive as separate filament slots in the 3MF. The Niederwald Monument takes the building color.

  6. File format

    You get a 3MF for Bambu Studio, OrcaSlicer or PrusaSlicer. Any of them can save it as STL if you need one.

About the Niederwald Monument

The Niederwald Monument (German: Niederwalddenkmal) is in Hesse, Germany, near Rüdesheim am Rhein, in the forest called the Niederwald. Built across the years 1871 to 1883, it marks the 1871 founding of the German Empire, after the Franco-Prussian War ended. It lies inside the Rhine Gorge, part of a larger UNESCO World Heritage Site. Its view takes in the Rhine Valley and, on the far bank, the town of Bingen. It is 38 m (125 ft) tall and represents the union of all Germans.

Emperor Wilhelm I laid the first stone on September 16, 1877. Johannes Schilling was the sculptor, with Karl Weißbach as architect. Its cost has been estimated at one million gold marks, and it was inaugurated on September 28, 1883. At its center is Germania, 12.5 m (41 ft) in height, seated on a throne decorated with eagles, holding the Imperial Crown in her right hand and the Imperial Sword in her left.

Beneath the pedestal sit levels decorated with laurel wreaths, ribbons and Iron Crosses; a lower level shows the arms of German states and an imperial eagle. A large relief shows Kaiser Wilhelm I riding a horse, with nobles, army commanders and soldiers beside him. Below it is a statue of Rhenus Pater handing a bugle horn to Mosella, his daughter. The Niederwald hill is broad and lies on the Rhine's right bank, with a dense summit forest of oak and beech and vineyards on its southern and western sides.

About this model

The Niederwald Monument is one of more than 6,500 landmark models in Mini Skyline. They are made with AI, and each one is checked in its real surroundings before release. Each model is written as code from public descriptions, plans, photographs and aerial views used only as references; no image or third-party model is copied into it. Everything around it is built from OpenStreetMap and Overture map data. Rights in the building itself, its name and any brands on it are not granted by Mini Skyline; clear them separately before you sell prints. If you would rather print the shape from map data, turn off Landmark models in the Buildings settings.

Mini Skyline is not affiliated with, or endorsed by, the owners of this building or its names and marks.

Keep exploring

More landmarks to print

Map data © OpenStreetMap contributors, Overture Maps; elevation Mapterhorn and Mapzen · Credits